- Stock: In Stock
- Model: 9464
- SKU: SAT3634
- Location: India
The SIM7600E-H 4G HAT is a 4G/3G/2G communication and GNSS positioning module, which supports
LTE CAT4 up to 150Mbps for downlink data transfer. it is pretty low power consumption. You can connect this 4G module with a computer to surf the Internet or attach it onto Raspberry Pi to enable functions like 4G high-speed connection, wireless communication, making telephone calls, sending SMS, global positioning, etc.
The SIM7600G-H 4G HAT supports telephoto calls and sending SMS by AT Commands using an onboard audio jack.
Waveshare SIM7600G-H 4G HAT For Raspberry Pi, LTE Cat-4 4G 3G 2G Support
Based on cloud communication it supports TCP/UDP/FTP/FTPS/HTTP/HTTPS communication protocol.
Waveshare SIM7600G-H 4G HAT For Raspberry Pi, LTE Cat-4 4G 3G 2G Support
What’s On Board:
Waveshare SIM7600G-H 4G HAT For Raspberry Pi, LTE Cat-4 4G 3G 2G Support (3)
SIM7600G-H
CP2102 USB to UART converter
NAU8810 audio decoder
TXS0108EPWR voltage translator: translates 3.3V/5V into 1.8V
MP2128DT power chip
MP1482 power chip
Raspberry Pi GPIO header
SIM7600 control interface: for connecting with host boards like Arduino/STM32
SIM card slot
supports 1.8V/3V SIM card
TF card slot
allows data storage like files, messages, etc.
3.5mm earphone/mic jack
USB interface
for testing AT Commands, getting GPS positioning data, etc.
USB to UART interface
for serial debugging, or log in to Raspberry Pi
MAIN antenna connector
AUX antenna connector
GNSS antenna connector
Power switch
Network status indicator
Power indicator
Operating voltage selection jumper
UART selection jumper
A: access Raspberry Pi via USB to UART
B: control the SIM7600 by Raspberry Pi
C: control the SIM7600 via USB to UART
PWR configuration jumper
PWR – 3V3: auto startup on power-up (default)
PWR – D6: startup/shut down by the Raspberry Pi D6 pin
Flight mode configuration jumper
NC by default, no flight mode control pin
Flight – D4: flight mode is controlled by the Raspberry Pi D4 pin
USB connector solder pads
BOOT forced programming solder pads
Note: this is a region-specific module, please check the supported bands before placing an order.
Features:
- Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
- Supports dial-up, telephone call, SMS, TCP, UDP, DTMF, HTTP, FTP, etc.
- Supports GPS, BeiDou, Glonass, LBS base station positioning
- Onboard USB interface, to test AT Commands, get GPS positioning data, and so on
- Onboard CP2102 USB to UART converter, for serial debugging
- Breakout UART control pins, to connect with host boards like Arduino/STM32
- SIM card slot supports 1.8V/3V SIM card
- TF card slot for storing data like files, messages, etc.
- Onboard audio jack and audio decoder for making a telephone call
- 2x LED indicators, easy to monitor the operating status
- Onboard voltage translator, the operating voltage can be configured to 3.3V or 5V via jumper
- Baudrate: 300bps ~ 4Mbps (default: 115200bps)
- Autobauding baudrate: 9600bps ~ 115200bps
- Control via AT commands (3GPP TS 27.007, 27.005, and V.25TER command set)
- Supports SIM application toolkit: SAT Class 3, GSM 11.14 Release 99, USAT
Package Includes:
1 x SIM7600G-H 4G HAT Board
1 x 360° foldable LTE Antenna
1 x Magnetic base GPS External Antenna (B) with 2-meter cable
2 x USB type A plug to Micro plug Cable (Small + Lomg)
1 x RPi screws and Standoff pack (2pcs)
2 x Antenna connector