This is the new APM 2.8 autopilot module. The sensors are exactly the same as with APM2.6, this version is ideal for use with multi-copters and rovers. The APM 2.8 is a complete open source autopilot system and the bestselling technology that on the prestigious 2012 Outback Challenge UAV competition..
₹6,999.00
Ex GST: ₹5,931.36
The KK2.1.5 is next big evolution of the first generation KK flight control boards. The KK2.1.5 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than ever. A host of multi-rotor craft ..
₹5,999.00
Ex GST: ₹5,083.90
CC3D EVO CopterControl Hardware FeaturesPowerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM.3-axis high-performance MEMs gyros and 3-axis high-performance&n..
₹1,199.00
Ex GST: ₹1,016.10
DJI NAZA-M V2 Multirotor Autopilot Controller set With GPS Supports nine multi-rotor configurations, the DJI NAZA-M V2 Multirotor Autopilot Controller set With GPS acts as the brains of the aircraft, managing pilot input and interpreting data from the various sensors, helping maintain a stable flyin..
₹22,499.00
Ex GST: ₹19,066.95
The DJI NAZA-M Lite V1.1 with GPS Kit is a simplified version of, and it inherits the high reliability and stability from the Naza M flight controller’s heritage. The Naza M Lite controller has an all-in-one design that means the installation is easy and straightforward while saving space and weight..
₹15,269.00
Ex GST: ₹12,939.83
It is a pre-programmed controller board with an onboard accelerometer and a Gyro sensor specially designed for UAVs. It can be used to design model aircraft, drones, quadcopters, etc.Features:Consists of Atmega 324 U Microcontroller On-board.Consists of an LCD Display on board for display purposes i..
₹3,100.00
Ex GST: ₹2,627.12
Characteristics:Compatible with Alexmos2.2 or firmware below, compatible with the newest firmware BruGi_050 German, standard Russian2.2 firmwareTipsA new generation of strong input control 32-bit processor, a circuit board with PX4FMU + PX4IOSpecifications:32-bit Pixhawk PX4 Autopilot Open Code Fli..
₹14,960.00
Ex GST: ₹12,677.97
This PIXHAWK 2.4.8 Full Combo Kit consists of all in one required product for the drone flight controller. find all product included in this kit at below package includes.PIXHAWK PX4 2.4.8 Flight Controller is a high-performance autopilot-on-module suitable for fixed-wing, multi-rotors, helicopters,..
₹14,960.00
Ex GST: ₹12,677.97
For entry-level enthusiasts, now brings out the most cost-effective solution, the DJI Naza-M Lite Multi-Rotor Flight Controller system. As the simplified version of NAZA-M, it inherits the high reliability and stability of NAZA-M. The innovative All-in-one design simplifies installation and sa..
₹6,199.00
Ex GST: ₹5,253.39
This PIXHAWK 2.4.8 Full Combo Kit consists of all in one required product for the drone flight controller. find all product included in this kit at below package includes.PIXHAWK PX4 2.4.8 Flight Controller is a high-performance autopilot-on-module suitable for fixed-wing, multi-rotors, helicopters,..
₹21,149.00
Ex GST: ₹17,922.88
Naze32 6DOF Flight Control board is the cheapest level naze 32 flight controller and does not include a magnetometer sensor or a barometer. Ideal for experienced FPV pilots who want a cheap but capable flight controllerNote:Flashing/Updating the Default firmware may cause a problem of connectivity w..
₹1,090.00
Ex GST: ₹923.73
Hot
The Latest version F3 Brushed Flight Control Board Based On SP Racing F3 EVO Brush for Micro FPV Frame brushed flight control supports 6-axis multi-rotors. The working current of each axis can reach 10A or higher.Upgraded voltage boost and reduction module provide 5V output and stable 500mAh current..
₹1,090.00
Ex GST: ₹923.73
Hot
Picking the right flight controller that suits your needs is always a daunting task… Don’t worry we Robu.in is here to assist you to get a quality product. Buy this Pixhawk 2.4.8 32 Bit PX4 Autopilot flight controller for your drone application. what are you have to do is just check it’s a specifica..
₹3,189.00
Ex GST: ₹2,702.54
This is a breakout cable for the Naze32 flight controller. The NAZE32 Receiver connecting cable specially designed for open-source flight controllers such as Naze32 to connect with a radio receiver, sturdy and durable.Package Includes:1 x Naze 32 6DOF receiver cable..
₹119.00
Ex GST: ₹100.85
This is an NX4 EVO Flight Controller. This Flight Controller Four-level flight modes are Beginner, Practice, Intermediate, Experts. This Flight Controller Supports a single aileron, dual ailerons, triangles, and V-tail. The input Voltage of This Flight Controller is about 5-6 volts and This Controll..
₹1,900.00
Ex GST: ₹1,610.17
This buzzer is used with Pixhawk and PX4 autopilot to annunciate status tones. The buzzer includes a two-position DF14 connector on one side that plugs directly into the Pixhawk or PX4 FMU board. The Passive buzzer has a JST-SH connector on one side that plugs directly into the Pixhawk. Once connect..
₹129.00
Ex GST: ₹109.32
This Pixhawk flight controller from RadioLink has optimized the PCB layout and the barometer height hold, providing more stable flight performance even at high speed. It integrated the newest 32-bit chip technology and high-end sensors, this is absolutely one of the best flight controllers for quadc..
₹19,499.00
Ex GST: ₹16,524.58
This is a Radiolink Mini Pix Flight Controller. This Flight controller has PIXHAWK Vibration Damping by this it can reduce the Motor vibration. Also, it has two telemetry Stream by which it can Transmit both Data and images. Image Transmission Depends upon the rated voltage of image Transmission. Th..
₹11,699.00
Ex GST: ₹9,914.41
You will get an STM32F405 FC (better than F411), onboard 4-level battery life indicator, 4GB Blackbox SD card slot for your flight logs, 4 groups of LED strip pads, complete with a DJI plug for your digital quad, and built-in Bluetooth for wireless configuration on the SpeedyBee app. Don’t forg..
₹7,749.00
Ex GST: ₹6,566.95
Built with a better Bluetooth/WiFi 2-in-1 chip for 33% faster wireless data transfer. Update FC firmware with your smartphone in just 1 minute! Connect this FC via Bluetooth and fully configure any setting forget flight/Emuflight/INAV as you want.Features:Flash your firmware 33% faster wirelessly + ..
₹13,499.00
Ex GST: ₹11,439.83
The world’s first FC board is compatible with the Silverware firmware. This is the most simple and affordable method to try whoop FPV racing hobby. Supports level mode and acro mode. Also, it has the ability to change settings for custom builds or to adapt to personal preferences by stick gestures. ..
₹879.01
Ex GST: ₹744.92
These Anti-Vibration fixed Screws are the pack of 4 screws that can be used to absorb and reduce vibrating shock from the quadcopter frame to the flight controller board, to protect it from damage as well as it provides tight-fitting on the frame. As high-frequency vibrations transmitted to th..
₹119.00
Ex GST: ₹100.85
AeroFC is the Latest Launch Triple Redundant Autopilot flight controller, which is based on an STM 32 microcontroller clocked at 216MHz. The IMU’s supports Dual redundant power inputs accelerometer, gyroscope, and magnetometer.The onboard STM 32 is isolated and dampened while reducing the interferen..
₹21,906.00
Ex GST: ₹18,564.41
If you are wandering to make your First DIY Drone. Then This Anti-vibration shock absorber is needed for you. The absorber is used to protect your flight controller from vibration while driving.This is a universal Glass Fiber Flight Controller Anti-Vibration Set Shock Absorber APM/KK/MWC/Pixhaw..
₹199.00
Ex GST: ₹168.64
Are you want to be an Electronic Geek in the future and want to build your own drone then this Flight controller is best for you. The flight controller uses the data gathered by the sensors to calculate the desired speed for each of the four motors. The flight controller sends this desired speed to ..
₹6,649.01
Ex GST: ₹5,634.75
This 6 in 1 CC3D Receiver Cable Suitable for MINI CC3D, standard CC3D, CC3D EVO. 1 x 6 in 1 CC3D Cable Set. Color Function JST-SH Pin Servo connector plug. Yellow PWM signal 3 or PWM outputCable color denotations:Black Ground 1 1.Red Power to RC RX-(VCC Unregulated) 4.8V-15V 2 1.White PWM signal 1 o..
₹139.00
Ex GST: ₹117.80
Flight Control Flip32 CC3D Shock Absorber Flight Control Damping Plate Shock Absorber FPV Aerial Essential for Mini QAV250/H250 QuadcopterIt absorbs vibration, the center supported plate is ideal for sensitive electronics and cameras. The flush flat-bottom mounting allows bolt or tape style attachme..
₹199.00
Ex GST: ₹168.64
Damping Plate Shock Absorber for CC3D Flip32 Naze32 Mini APM Flight controller is a small but very essential component in building the quadcopter or any RC drone using flight Controller to protect them from vibration while flying as well as with landings.It absorbs vibration, the center supported pl..
₹199.00
Ex GST: ₹168.64
DF13 4 Pin Flight Controller communication cable uses the Hirose DF13 series connector. It is 20 cm long and it is designed to be used on the APM and PX4 board series. It is typically used between the PixHawk and the GPS receiver module.These cables have a good temperature resistive silicon fle..
₹49.01
Ex GST: ₹41.53
DF13 5 Pin Flight Controller communication cable uses the Hirose DF13 series connector. It is 20 cm long and it is designed to be used on the APM and PX4 board series. It is typically used between the PixHawk and the GPS receiver module.These cables have a good temperature resistive silicon fl..
₹79.00
Ex GST: ₹66.95
DF13 6 Pin Flight Controller communication cable uses the Hirose DF13 series connector. It is 20 cm long and it is designed to be used on the APM and PX4 board series. It is typically used between the PixHawk and the GPS receiver module.These cables have a good temperature resistive silicon fl..
₹89.00
Ex GST: ₹75.42
The new 4in 1 EMAX Magnum Mini stack features F4 flight controller board OSD, MPU6000 gyro, connected via fast SPI. This 4in1 ESC has BLHELI_32 supporting 35A current rating. That huge Amp rate means you can use this mini-stack for 5″ quads! This stack supports from 3S up to today’s modern 6S b..
₹7,799.00
Ex GST: ₹6,609.32
Flip32 OMNIBUS F4 Flight Controller is new generation F4 hardware flight controller for FPV race with STM32F405 MCU.The Flip32 Omnibus flight controller uses the MPU6000 over SPI for the best possible flight performance. Along with the MPU6000 are a and an AB7456 OSD chip (an upgraded MAX7456) for t..
₹2,599.00
Ex GST: ₹2,202.54
Pixhawk 4 is the latest update to the successful family of Pixhawk flight controllers. It is designed and developed in collaboration with Holybro and the PX4 team, optimized to run the full Dronecode stack and comes preinstalled with the latest PX4 firmware (v1.7).The Pixhawk 4 features a new smalle..
₹33,399.00
Ex GST: ₹28,304.24
M3 Anti Vibration Rubber Damper Balls For FPV F4, F7 Flight Controller. An M3 anti-vibration mounts rubber balls for the flight controller Board. These rubber damper balls can effectively help to reduce the sensitivity of the flight controller, is a must-have item for every pilot who pursuit of extr..
₹49.01
Ex GST: ₹41.53
M3 Shock Absorber Screws is the pack of 4 screws that can be used to absorb and reduce vibrating shock from the quadcopter frame to the flight controller board; to protect it from damage as well as it provides tight-fitting on the frame. As high-frequency vibrations transmitted to the vehicle abatem..
₹149.00
Ex GST: ₹126.27
M3 Shockproof Sponge Pads are very useful and widely used for mini multi-rotor quadcopters Such as DIY mini ZMR-180, QAV210, QAV250, ZMR250 and much more FPV racing quadcopter.These super-light, strengthen shockproof, Anti-Static 3M Ultralight EVA shockproof mounting pads, 11±1mm thickness, Ensure s..
₹99.00
Ex GST: ₹83.90
The Mamba F405 Stack is introduced as more and more requests for a budget stack. With 4 x 35A Escs built into the stack, you now have plenty of room for spikes. If you are running 4S Lipo to power your quad there is absolutely no advantage in running 40A Esc.You will now be able to complete yo..
₹4,959.00
Ex GST: ₹4,202.54
This is the all-new Mamba F405 Flight Controller with BEC based on the design of the popular F4. However, the main advantage of this board is that uses the more powerful STM32 processor for even faster loop times. Low noise MPU6000 IMU connected via SPI, a current and voltage sensor, etc.The F..
₹1,989.00
Ex GST: ₹1,685.59
The Matek F405-OSD Flight Controller comes with lots of features. From the high-speed, 168MHz, 32bit F405 processor to BetaFlight firmware and OSD this flight controller has the power to easily control your drone. It also has a black box to help you fine-tune your drone or to help determine what wen..
₹2,499.00
Ex GST: ₹2,117.80
The Micro Minim OSD is the next evolution of minimization. The Minimosd was engineered to bring users a very powerfull OSD at an unreal cost. From the manufacturers of the WitesSpy KV Team OSD and all your requests have now evolved into the Micro MinimOSD! After all the community mods, they re-engin..
₹649.00
Ex GST: ₹550.00
The Mini APM3.1 Flight Controller with Power Module for Multicopter FPV board is a modified version of the APM2.6 board but made to be as small as possible. Measuring just 35×35 mm big it still includes the same features and sensors as the full-size APM2.6 board making this a great system to u..
₹3,499.00
Ex GST: ₹2,965.25
Mini OSD for Pixhawk Flight Controller has a companion OSD board called MinimOSD. It reads all the MAV Link data in the APM telemetry stream and overlays it on the video stream if you’re using an onboard camera and wireless video transmitter. This is useful if you’re flying in First Person View (FPV..
₹1,299.00
Ex GST: ₹1,100.85
This Mini OSD FOR APM 2.6 AND APM 2.8 is a mini Arduino based on-screen display board. It’s tailored for use with ArduPilot Mega and the MAVlink protocol and designed to be as small as possible.Its main components are an ATmega328P 8 bit microcontroller with an Arduino bootloader and a MAX7456 monoc..
₹1,299.99
Ex GST: ₹1,101.69
Mini USB (90° Connector) to FPV AV Video Output Cable for GoPro Hero 3 is a 100% Brand new and high-quality cable. It features Video/Audio output from the camera’s USB port to your video transmitter or monitor. This cable has a 90 degree USB connector so you can fit the cable more securely to the ca..
₹199.00
Ex GST: ₹168.64