- Stock: In Stock
- Model: 10292
- SKU: SAT4462
- Location: India
ODROID-N2+ is a revision from ODROID-N2.
– Maximum CPU clock of Quad-core Cortex-A73 is increased to 2.4Ghz from 1.8Ghz.
– Maximum CPU clock of Dual-core Cortex-A53 is increased to 2.0Ghz from 1.9Ghz.
– On-board RTC backup battery holder is mounted on the board.
The main CPU is based on big.Little architecture which integrates a quad-core ARM Cortex-A73 CPU cluster and a dual core Cortex-A53 cluster with a new generation Mali-G52 GPU.
Thanks to the modern 12nm silicon technology, the A73 cores run at 2.2Ghz without thermal throttling using the stock metal-housing heatsink allowing a robust and quiet computer.
The CPU multi-core performance is around 20% faster and the GPU is 10% faster than the N1. The N2+’s DDR4 RAM is running at 1320Mhz with 1.2volt low power consumption.
The large metal housing heatsink is designed to optimize the CPU and RAM heat dissipation and minimize throttling. The CPU is placed on the bottom side of the PCB to establish great thermal characteristics.
Board Detail
- A. S922X CPU
- B. 4 x DDR4 RAM
- C. 1 x RJ45 Ethernet Port (10/100/1000)
- D. 1 x HDMI 2.0
- E. 4 x USB 3.0
- F. 2 x System LED Indicators
- G. 1 x DC Power Jack
- H. 1 x AV Out (Stereo Audio with Composite video)
- I. 1 x Micro USB2.0 OTG
- J. 1 x SPI Flash 8MiB
- K. 1 x SPI Boot Select Switch
- L. 1 x eMMC Module Socket
- M. 1 x Micro SD Slot
- N. 1 x IR Receiver
- O. 1 x RTC Backup Battery Holder
- P. 1 x Active Cooling Fan Connector (2-pin)
- Q. 40 x GPIO Pins
- R. 1 x UART for System Console
SBC Specification
| Form Factor | Board Dimensions: 90mm x 90mm x 17mm |
| Heatsink Dimensions: 100mm x 91mm x 18.75mm | |
| Weight: 200g including heatsink | |
| Processor | Amlogic S922X Processor (12nm fab) |
| Quad-core Cortex-A73(up to 2.4Ghz) and Dual-core Cortex-A53 (up to 2Ghz) | |
| ARMv8-A architecture with Neon and Crypto extensions | |
| Mali-G52 GPU with 6 x Execution Engines (800Mhz) | |
| Memory | DDR4 4GiB or 2GiB with 32-bit bus width |
| Data rate: 2640 MT/s (PC4-21333 grade) | |
| 1.2Volt low power design | |
| Storage | 1 x eMMC connector (8G, 16G, 32G, 64G and 128G are available) |
| 1 x microSD slot (DS/HS modes up to UHS-I SDR104) | |
| Networking | 1 x GbE LAN ports (RJ45, supports 10/100/1000 Mbps) |
| * Green LED: Flashing by data traffics at 100Mbps connection | |
| * Amber LED: Flashing by data traffics at 1000Mbps connection | |
| Optional WiFi USB adapters | |
| Video | 1 x HDMI 2.0 (up to 4K@60Hz with HDR, CEC, EDID) |
| 1 x Composite video (3.5mm jack) | |
| Audio | 1 x Stereo Audio line-out (3.5mm jack) |
| 1 x HDMI digital output | |
| 1 x Optional SPDIF optical output | |
| External I/O | 4 x USB 3.0 Host ports (shares one single root hub) |
| 1 x USB 2.0 OTG port for Host or Device mode. (No power input) | |
| 1 x Debug serial console (UART) | |
| 1 x Peripheral Expansion Header (40-pin, 2.54mm pitch) | |
| Other features | On board RTC(Real Time Clock) IC to keep date and time. A CR2032 coin battery holder was replaced with the 2-pin 1.25mm pitch connector. |
| No battery is included in the board. | |
| Please purchase the very common bare CR2032 cell from your local store. | |
| You can keep the RTC time up to several years with a 200mAh CR2032 battery. | |
| 8MiB SPI Flash for boot manager | |
| IR receiver for remote controller | |
| Built with a large passive heatsink | |
| System LEDS Indicators: Red, Blue | |
| Active Cooling Fan Connector (5V 2-pin) | |
| Power | 1 x DC jack : outer (negative) diameter 5.5mm, inner(positive) diameter 2.1mm |
PACKAGE INCLUDES:
1 x ODROID-N2+ with 2GB RAM