Search Criteria
Products meeting the search criteria
The LilyTiny is a tiny little LilyPad board designed to add flashy functionality to your project without taking up a lot of room.Even though it’s as small as some of the LilyPad sensors, this board actually has an ATtiny microcontroller on it so it’s actually pretty smart!Simply sew on 4 LEDs and co..
₹199.00
Ex GST: ₹168.64
This Transparent case designed for the Raspberry Pi 2 B and Model B+(B Plus) to give you maximum use of the Raspberry Pi, it provides openings for all the connectors( 3.5mm Audio / Micro USB Power / HDMI Video / Ethernet/ 40 Pin GPIO/ DSI/ USB ports) and comes with four screws that will keep the cas..
₹149.00
Ex GST: ₹126.27
A Standard Active Alarm Module for Arduino is an audio signaling device, which may be mechanical, electromechanical, or piezoelectric. This PCB Mounted Active Buzzer Module can produce a range of sound tones depending on the input frequency, i.e it can generate tones between 1.5 to 2.5 kHz by switch..
₹59.00
Ex GST: ₹50.00
DS18B20 Temperature Sensor Module is a Digital temperature sensor DS18B20 that will tell you temperature with 9 to 12-bit resolution! Uses only 1 wire to the Arduino or other microcontroller for communication. With the One Wire protocol, you can operate a large number of these sensors from one Ardui..
₹129.00
Ex GST: ₹109.32
This is a 10K ohm Negative Temperature Coefficient (NTC) thermistor.NTC Thermistor is one of the most commonly used temperature sensors. In an NTC the resistance value decreases as the temperature increases.NTC 10K can be applied to air conditioner devices,heating devices,clinical thermometer, auto ..
₹13.99
Ex GST: ₹11.86
The Keypad 4x3 features a total of 12 buttons in Matrix form. This is a membrane keypad with no moving parts. A female 7-pin berg connector is provided for interfacing it with your microcontroller circuits. Convenient adhesive backing provides a simple way to mount the keypad in a variety of applica..
₹89.00
Ex GST: ₹75.42
This Matrix Keypad 4 X 4 has 16 buttons, arranged in a telephone-line 3x4 grid with a column of 4 characters (A, B, C, and D). The keys are connected into a matrix, hence only 8 microcontroller pins (4-columns and 4-rows) are required to scan the pad. This 16-button keypad provid..
₹99.00
Ex GST: ₹83.90
This small 3.5 inch touch screen Raspberry Pi Display module is designed especially for Raspberry Pi, using the latest Linux Core system. This is ideal for DIY anywhere, anytime and does not require any separate power source or case to hold it. The module sits right on top of Pi and an ideal alterna..
₹1,499.00
Ex GST: ₹1,270.34
The transmitter module is very simple to operate and offers low current consumption (typical. 11mA). Data can be supplied directly from a microprocessor or encoding device, thus keeping the component count down and ensuring a low hardware cost. This hybrid RF Transceiver Module provides a complete R..
₹196.67
Ex GST: ₹166.67
Fingerprint scanners are awesome! Why use a key when you have one right at the tip of your finger? Unfortunately, they’re often unreliable or difficult to implement. Well not anymore! This great GT-521F32 fingerprint module from ADH-Tech communicates over TTL Serial so you can easily embed it into y..
₹1,769.00
Ex GST: ₹1,499.15
This Sensor Shield expansion board retains the advantages of version V4.0 on the basis of stack design, PCB Immersion Gold processing technology. newly added many kinds of interface, for example, IIC interface, 32 channels servo motor interface, Bluetooth communication module interface, SD Card comm..
₹136.00
Ex GST: ₹115.25
Arduino Uno Protoshield directly fits into an Arduino UNO board and breaks out the I/O pins and makes it an expansion board. It makes it very easy to design any customer circuit. You can directly solder components on the board or connect the circuit using 170 point mini breadboard (included). The bo..
₹135.00
Ex GST: ₹114.41
The Bluetooth Module is the latest Bluetooth wireless serial cable! This version of the popular Bluetooth uses the HC – 05 / 06 modules. These modems work as a serial pipe. Any serial stream from 9600 to 115200 bps can be passed seamlessly from your microcontroller to your target. You will need..
₹249.00
Ex GST: ₹211.02
The Arduino Ethernet Shield allows an Arduino or Arduino compatible board to connect to the internet. It is based on the Wiznet W5100 ethernet chip providing a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sk..
₹499.00
Ex GST: ₹422.88
The GY-271 is supposed to have an HMC5883L, but some boards have a QMC5883L which has the same basic capability, but is not compatible with the H. The GY-271 QMC5883L 3-axis Electronic Compass Module Magnetic Field Sensor is designed for low field magnetic sensing with a digital interface and it is ..
₹247.00
Ex GST: ₹209.32
The Compass Module 3-Axis HMC5883L is a low-field magnetic sensing device with a digital interface.The compass module converts any magnetic field to a differential voltage output on 3 axes. This voltage shift is the raw digital output value, which can then be used to calculate headings or sense magn..
₹249.00
Ex GST: ₹211.02
This hm-10 Bluetooth module with BLE 4.0 support, Internal with logic level conversion circuit. No external 5V level to turn into a 3.3V level Power input with anti-anti-circuit. Avoid accidental power plug reversed. Generally, users are using the HC-05 Bluetooth module but it doesn't support w..
₹329.00
Ex GST: ₹278.81
The default function of the capacitor touch dimmer is a switch, dimming, with brightness memories LED touch dimming. It will light slowly when turning on the lights, and become dark slowly when turn off, which effectively avoid the stimulation to eyes. The lamp brightness can be adjusted by requirem..
₹109.00
Ex GST: ₹92.37
MCP23017 is a high-speed IIC interface. It supports the IIC frequency of 100KHz, 400KHz, and 1.7MHz. The chip has 3 address pins, which can set up to 8 different addresses. So 8 modules can be connected through two IIC buses to achieve up to 128 IO extensions.This module is flexible in configuration..
₹399.01
Ex GST: ₹338.14
The MPR121 is a capacitive touch sensor controller driven by an I2C interface. The chip can control up to twelve individual electrodes, as well as a simulated thirteenth electrode. The MPR121 also features eight LED driving pins. When these pins are not configured as electrodes, they may be used to ..
₹199.00
Ex GST: ₹168.64
The MQ-5 is used in gas leakage detecting equipment in consumer and industry applications, this sensor is suitable for detecting LPG, natural gas, coal gas. Avoid the noise of alcohol, cooking fumes, and cigarette smoke. The sensitivity can be adjusted by the potentiometer. The sensitive material of..
₹140.00
Ex GST: ₹118.64
This is a simple-to-use MQ-6 Liquefied Petroleum Isobutane Propane Gas Sensor module, suitable for sensing LPG (composed of mostly propane and butane) concentrations in the air. The MQ-6 can detect gas concentrations anywhere from 200 to 10000ppm. This sensor has high sensitivity and fast response t..
₹140.00
Ex GST: ₹118.64
This wireless Transceiver module is an easy and suitable module if you want to set up your wireless communication system at a low cost!! It can achieve a good balance between wireless transition performance and cost! This module comes with the 2.4G antenna (2DB), with a 250Kbps transmission rat..
₹234.01
Ex GST: ₹198.31
PAM8403 is a small digital amplifier chip, high-definition sound quality highlights the advantages of digital chips, the circuit using the most reasonable peripheral configuration, power supply filtering is upgraded to 470uf.Note!!! Please make sure the power supply is not more than 5.5V and pl..
₹95.00
Ex GST: ₹80.51
The XD-216 Screw Shield Expansion Board can be plugged into the Arduino controller. You can use this shield to save yourself from a bad port connection. Feel secure with this Arduino-compatible screw shield.Both sides of the shield are broken out to the side of the Arduino, to allow access to everyt..
₹440.00
Ex GST: ₹372.88
TTP223 Touch Key Module is based on a touch-sensing IC capacitive touch switch module. A capacitive touch sensor module based on the dedicated TTP223 touch sensor IC. The module provides a single integrated touch sensing area of 11 x 10.5mm with a sensor range of ~5mm.An onboard LED will give a visu..
₹38.94
Ex GST: ₹33.00
TTP223B Capacitive Touch Key Sensor Module is based on a touch-sensing IC capacitive touch switch module. It allows you to remove the worry of conventional push-type keys.Digital Capacitive Touch Switch Module is based on TTP223B. Normally, it outputs low and keeps at a low power state. When a touch..
₹92.04
Ex GST: ₹78.00
The 4 Channel Capacitive Touch Sensor Module uses the touch-sensing IC TTP224 to sense the touch input thus making it easy to add capacitive touch input to your project. The touching detection IC is designed for replacing the traditional direct button key with a diverse pad size. The module has 4 to..
₹119.00
Ex GST: ₹100.85
The TTP226 is a touchpad detector IC which offers 8 touch key. The touching detection IC is designed for replacing the traditional direct button key with a diverse pad size. Capacitive touch allows electronics to sense when your finger is within a few millimeters of a surface to simulate a button “p..
₹129.00
Ex GST: ₹109.32
This is TTP229 16-Way Capacitive Touch Switch Digital Touch Sensor Keypad Module. This capacitive touch sensor module uses the TTP229 integrated circuit, making it easy to add capacitive touch input to your project. It features 16 sensitive touchpads that make an ideal replacement for the old fashio..
₹124.58
Ex GST: ₹124.58
Features:Polycrystalline silicon, with higher transfer efficiency output and environment-friendlySuitable for charging a cellphone or DIY chargerSize: 270 x 180 x 2mmPower: 5WVoltage: 12VType: Other Camping GearColor: BlackPackage Includes:1 x 5W 12V Solar Panel...
₹699.00
Ex GST: ₹592.37
The four spindles on the ICSH044A Blackberry Trackball Breakout Board 360 Degree Trajectory Ball Module Hall Effect Sensor have a tiny circular magnet in the end; each of these is paired with an SMD hall effect sensor, which is used to measure up, down, left, and right movements of the trackball.An ..
₹589.00
Ex GST: ₹499.15
PAM8403 5V Two-Channel Stereo Audio Amplifier Module is based on PAM8403 which is a 3W+3W, class-D audio amplifier. Allowing it to achieve high-quality sound reproduction. The new filterless architecture allows the device to drive the speaker directly, requiring no low-pass output filters, thus savi..
₹67.00
Ex GST: ₹56.78
Features:Voltage: 6 V (Max)Current: 100mA (Max) Size: 7cm X 7cmApplication:To charge cell phonesFor home lightingFor DIY solar power toysSuitable for solar powered water pump, small solar power system, etc...
₹149.00
Ex GST: ₹126.27
Description:Item NO.: A2212Dimension: 27.8*27mmShaft diameter: 3.17mmMax Efficiency: 80%Max Efficiency Current: 4-10A (>75%)Current Capacity: 12A/60sNo Load Current @ 10V: 0.5ANo. Of Cells: 2-3 Li-PolyWeight: 65gKV: 1000Suitable for the propeller size: 1047,1060,9050Color: black,silver,yell..
₹414.99
Ex GST: ₹351.69
Description:Item NO.: A2212Dimension: 27.8*27mmShaft diameter: 3.17mmNo. Of Cells: 2-3 Li-PolyWeight: 65gKV: 1400Recommended Propeller: 8060(3s),9050(2s)Package Included:1 x A2212 KV1400 Brushless Motor1 x motor mount1 x clip4 x screw..
₹499.00
Ex GST: ₹422.88
D2826 is a brushless motor with a 1100kv rating. Brushless motors are synchronous motors which are powered by a DC electric source via an integrated inverter/switching power supply, which produces an AC electric signal to drive the motor. In this context, AC, alternating current, does not imply a si..
₹999.00
Ex GST: ₹846.61
Description:Item Name:30A SimonK Procedure Brushless ESCInput Voltage: (2-3S Lixx red)Drive Current: 30A (Max: 40A/10S)Size 50x23x8BEC:5V/3AWeight: 25gFeatures:1).This hardware, with the SimonK firmware, gives you the perfect solution for multirotor use;2).Highest efficiency 100% N-FET design;3).Hig..
₹399.01
Ex GST: ₹338.14
Motor:Specifications:Model NO.: A2212Dimension: 27.8*27mmShaft diameter: 3.17mmMax Efficiency: 80%Max Efficiency Current: 4-10A (>75%)Current Capacity: 12A/60sNo Load Current @ 10V: 0.5ANo. Of Cells: 2-3 Li-PolyWeight: 65gKV: 1000Suitable for the propeller size: 1045, 1047,1060, 9050ESC:Des..
₹759.00
Ex GST: ₹643.22
Motor:SPECIFICATIONS:Model NO.: A2212Dimension: 27.8*27mmShaft diameter: 3.17mmMax Efficiency: 80%Max Efficiency Current: 4-10A (>75%)Current Capacity: 12A/60sNo Load Current @ 10V: 0.5ANo. Of Cells: 2-3 Li-PolyWeight: 65gKV: 1000Suitable for the propeller size: 1045, 1047,1060, 9050ESC:DES..
₹779.00
Ex GST: ₹660.17
Specification:Item Name: F550 550mm Hexa-Rotor Racing Frame KitWheelbase: 550mmMaterial of Frame Arm: Fiber + NylonColor of Arm: White + Black + RedWeight: 424g- Can directly connect the ESC and power cable to center boardRecommend Parts:Motor: 2312 MotorESC: 30-40A ESCPropeller: 1045 CW CCW Propell..
₹1,899.00
Ex GST: ₹1,609.32
Description:Item name: QAV250 Frame KitArm plate thickness: 3mmMain material: carbon fiberWheelbase: 250mm Recommend parts (package not include):Propeller: 5 inchMotor: 1806 2204 2206ESC: 8A-12ABattery: 1300Mah-2200MahPackage included:1 x QAV250 Frame Kit..
₹1,199.00
Ex GST: ₹1,016.10
Description:B6AC Charger is a multi-function charger, it supports dual input, is to use the built-in high-performance microprocessor controlled high-tech and professional software for fast charge / discharger, which supports rechargeable battery types include: Li-ion , Li-Poly, Li-Fe, NiCD, NiMh and..
₹2,799.00
Ex GST: ₹2,372.03
This is the new APM 2.8 autopilot module. The sensors are exactly the same as with APM2.6, this version is ideal for use with multi-copters and rovers. The APM 2.8 is a complete open source autopilot system and the bestselling technology that on the prestigious 2012 Outback Challenge UAV competition..
₹6,999.00
Ex GST: ₹5,931.36
The KK2.1.5 is next big evolution of the first generation KK flight control boards. The KK2.1.5 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than ever. A host of multi-rotor craft ..
₹5,999.00
Ex GST: ₹5,083.90